Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Exactly How to Install a Bath Tub: Install an Acrylic Tub and Also Tub Surround
Blog Article
Here in the next paragraph yow will discover a good deal of helpful data concerning A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily easily accessible, the task can move immediately; if you have to open a wall surface to remove the old tub and also position the brand-new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will need an assistant to move out the old tub as well as embeded in the new one. Make certain you have actually qualified yourself for the work and also are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to think about using one before you begin. Possibilities are you may require a specialist plumber to make tube connections.
This short article will aid you mount a new bath tub in your restroom if you have currently acquired a new tub and don't require to alter the plan of your previous water system pipelines.
Your devices and material checklist ought to make up the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is separate the water supply. After doing so, turn on the taps to drain any water remaining in the system. The process of removing the existing taps can be quite problematic because of the restricted access that is typically the situation.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the faucets. Have a towel all set for the continuing to be water that will certainly originate from the pipelines. When the supply pipes have been removed, use the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. As soon as the faucets have actually been eliminated, the holes in the bath/basin will certainly need to be cleaned up of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipe links on the old faucets to the new taps. If the old taps are longer than the brand-new faucets, then a shank adapter is required for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the current supply pipelines.
If you need to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the mounting opening in the bath/basin guaranteeing that the washing machines remain in place in between the faucet and the sink. Safeguard the faucet in place with the supplier supplied backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous type should be attached to the tap finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been linked.
Mounting the Tub
Using both wooden boards under its feet, put the bathtub in the needed position. The wood boards are useful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The next goal is to make certain that the tub is leveled all round. This can be attained by inspecting the level and readjusting the feet on the bathtub up until the spirit level checks out degree.
To install faucets, fit all-time low of the furthest adaptable tap port to the ideal supply pipe by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water as well as examine all joints as well as brand-new pipework for leaks as well as tighten them if essential. Fill the tub as well as also inspect the overflow electrical outlet and the typical electrical outlet for leakages.
Ultimately, repair the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as securing around the bath tub ought to wait up until the bathtub has been made use of at the very least once as this will resolve it right into its final position.
Getting ready for the Installment
Firstly, the supporting framework provided with the bathroom should be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bathtub. When fitting the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the tub.
Fit the versatile faucet ports to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipe to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the provided washing machines.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last setting.
Tiling Around the Bathtub
In the area where the bathroom fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a rigid seal, creating the water to pass through the wall surface between the bath and also the tiling, causing issues with dampness and also feasible leaks to the ceiling below.
You can pick from a selection of coloured sealants to blend in your components as well as fittings. They are sold in tubes and also cartridges, as well as are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a bigger gap to load, you can load it with twists of drenched paper or soft rope. Remember to constantly fill up the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in usage. The sealant can fracture relatively early if you do not think about this motion before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the floor tiles utilizing waterproof or water resistant adhesive as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I was made aware of that article on How to Install a Bathtub through an associate on another web property. Sharing is caring. Helping others is fun. Thanks a lot for your time. Visit us again soon.
Book Your Service
Report this page